收藏本站
Q48S08120 DC-DC Converter Data Sheet
36-75 VDC Input; 12 VDC @ 8A Output
Q Family
When using remote sense, the output voltage at the con-
verter can be increased by as much as 10% above the
nominal rating in order to maintain the required voltage
across the load. Therefore, the designer must, if necessary,
decrease the maximum current (originally obtained from the
derating curves) by the same percentage to ensure the con-
Vin
Vin (+)
ON/OFF
TM
Converter
(Top View)
Vout (+)
SENSE (+)
TRIM
SENSE (-)
R T-INCR
Rload
verter’s actual output power remains at or below the maxi-
mum allowable output power.
Vin (-)
Vout (-)
Output Voltage Adjust /TRIM (Pin 6)
The converter’s output voltage can be adjusted up 10% or
down 20% relative to the rated output voltage by the addition
of an externally connected resistor.
The TRIM pin should be left open if trimming is not being
used. To minimize noise pickup, a 0.1 μ F capacitor is con-
nected internally between the TRIM and SENSE(-) pins.
To increase the output voltage, refer to Fig. 4. A trim resistor,
Fig. 4: Configuration for increasing output voltage .
R T ? DECR = Required value of trim-down resistor [k ? ]
and ? is as defined above.
Note: The above equations for calculation of trim resistor
values match those typically used in conventional industry-
standard quarter bricks.
Q Family
R T-INCR , should be connected between the TRIM (Pin 6) and
SENSE(+) (Pin 7), with a value of:
Vin (+)
TM
Converter
(Top View)
Vout (+)
SENSE (+)
R T ? INCR =
5.11(100 + ? )V O ? NOM ? 626
1.225 ?
? 10.22 [k ? ]
Vin
ON/OFF
Vin (-)
TRIM
SENSE (-)
Vout (-)
R T-DECR
Rload
where,
R T ? INCR = Required value of trim-up resistor k ? ]
V O ? NOM = Nominal value of output voltage [V]
Fig. 5: Configuration for decreasing output voltage.
? =
(V O - REQ ? V O - NOM )
V O - NOM
X 100 [%]
Trimming/sensing beyond 110% of the rated output voltage
is not an acceptable design practice, as this condition could
cause unwanted triggering of the output over-voltage protec-
tion (OVP) circuit. The designer should ensure that the dif-
V O ? REQ = Desired (trimmed) output voltage [V].
When trimming up, care must be taken not to exceed the
converter‘s maximum allowable output power. See previous
section for a complete discussion of this requirement.
To decrease the output voltage (Fig. 5), a trim resistor,
R T-DECR , should be connected between the TRIM (Pin 6) and
SENSE(-) (Pin 5), with a value of:
ference between the voltages across the converter’s output
pins and its sense pins does not exceed 1.20 V, or:
[V OUT ( + ) ? V OUT ( ? )] ? [V SENSE ( + ) ? V SENSE ( ? )] ≤ 1.20 [V]
This equation is applicable for any condition of output sens-
ing and/or output trim.
R T ? DECR =
where,
511
?
? 10.22 [k ? ]
APR 29, 2003 revised to NOV 20, 2006
Page 6 of 14
www.power-one.com
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
Q48T08120-NBB0 DC/DC QTR BRICK 96W 12V T/H
Q48T25018-NBB0 DC/DC QTR BRICK 45W 1.8V
Q48T25033-NBB0 DC/DC QTR BRICK 83W 3.3V T/H
Q48T30015-NBB0 CONV DC-DC 48V IN 1.5V OUT 45W
Q48T30018-NBA0 DC/DC QTR BRICK 54W 1.8V T/H
Q48T30025-NDB0 DC/DC QTR BRICK 75W 2.5V T/H
Q48T30033-NAAC DC/DC QTR BRICK 100W 3.3V T/H
QAK2J335KTP CAP FILM 3.3UF 630VDC AXIAL
相关代理商/技术参数
Q48S08120-PS00G 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸:
Q48S08120-PS0P 制造商:Power-One 功能描述:DC/DC PS SGL-OUT 12V 8A 8PIN QUARTER-BRICK - Bulk
Q48S08120-PS0PG 制造商:Power-One 功能描述:DC/DC PS SGL-OUT 12V 8A 8PIN QUARTER-BRICK - Bulk
Q48S15050-NS00 制造商:POWER1 功能描述:
Q48S15050NS00G 制造商:Power-One 功能描述:36-75VIN 5VOUT 15A / SMT / NEG ENABLE ROHS - Bulk
Q48S15050-NS00G 制造商:Power-One 功能描述:Module DC-DC 1-OUT 5V 15A 8-Pin Quarter-Brick 制造商:Power-One 功能描述:DC/DC PS SGL-OUT 5V 15A - Bulk
Q48S20015-NS00G 制造商:Power-One 功能描述:DCDC,HAZMAT - Bulk
Q48S20015-PS00G 制造商:Power-One 功能描述:DCDC,HAZMAT - Bulk